Smart Range Extending W-MUS Devices

Devices for extending the range between the meter and gateway

These OMS Compatible Wireless M-BUS repeater and Range extender is range of devices that are specific designed to extend the range between the meter and the gateway.

In lots of installation there is a need for longer range between the meter and the gateway. In order to address these demands Lansen has developed a complete range of devices that makes your installation cheaper and more robust to disturbances.

Using Lansen Range extender and the Lansen Repeaters the range between you existing gateway and meter will increase considerable.

OMS Wireless M-BUS Repeater

Lansen OMS Wireless M-BUS Repeater Wireless M-BUS Repeater for T,C and S mode,  are designed for the wireless M-BUS protocol  EN13757-3/4:2013 S1-M, C1 and T1. The devices are compatible with OMS (Open Metering System)  but also supports custom features such as routing.
The devices have sleek design and are easy to install.

Key features of these devices are:

  • Extend the range between meter and gateway.
  • IP 67 enclosure for outdoor mounting
  • Super long battery lifetime or internal AC/DC
  • Multihop support for extended range.

Wireless MBUS Range Extender

Lansen Range Extender for T,C and S mode,  are designed for the wireless M-BUS protocol  EN13757-3/4:2013 S1-M, C1 and T1. The devices are compatible with OMS (Open Metering System)

Key features of these devices are:

  • DIN rail mount.
  • Super easy installation no software needed
  • Seamless installation between antenna and gateway.
  • Will give up to 2x the range or more.
  • Extensive filtering against LTE/GPRS etc.
  • Support AC and DC

Wireless MBUS Range Extender

Increasing the performance of your existing gateway.

Wireless M-BUS range extender
GENERAL
The Lansen FAMP (Filtered Amplifier) for Wireless MBUS C1,T1 and S1 mode drastically increases the receiver performance of the gateway.
The Lansen FAMP is seamless mounted between the antenna and the gateway using standard SMA connector. The device is DIN mountable and can be mounted either vertical or horizontal depending on version. The robust shielded enclosure,
high quality components, together with clear LED indications ensures easy installation and long service life.

PERFORMANCE
The device amplifies the wanted signal and filters the incoming signal and removes disturbances from 4G, LTE, TV, WLAN
etc. By using the Lansen FAMP the wireless range of the gateway can be increased up to 2x or even higher if used in areas
where the disturbances are high. The extended filtering of the power ensures that the device will operate optimal independentof power source.

DEVICES
The range extenders are available in 2 versions:

LAN-WMBUS-FAMP868-LP
LAN-WMBUS-FAMP868 Standard as the image.

For more information please contact us or check the data-sheet [link]

Wireless M-BUS Repeater 3 jump support New generation R3, high sensitivity och long range.

Increase the range between meter and gateway using these highly configurable high performance repeaters

Wireless M-BUS Repeater ACDC

LAN-WMBUS-R3-M
Battery repeater

Wireless M-BUS Repeater ACDC

LAN-WMBUS-R3-M Mains powered repeater

New generation R3, higher sensitivity, longer range, 2 antennas and longer battery lifetime.


GENERAL

The Wireless M-BUS Repeater is a plug-and-play and highly configurable repeater for extending the range between a device and a collector. The device is available with internal antenna high performance antenna. The enclosure
is chosen to make the repeater as discrete as possible.

ROUTING
The advanced collision avoidance algorithm minimizes problems with collisions and data repetition. The device support 3 jump between the meter and GW while still complying with the OMS Wireless MBUS standard.

CONFIGURATION
All devices could be used right out of the box but they are also highly configurable. It is for example possible to configure
the “suppression” timer to set the number of minutes before a data from a specific device should be routed again.
For the multihop repeater is possible to setup the static routing used by the repeater, to allow safe multihop operation. All configuration information is maintained even during battery change and powerloss.

PERFORMANCE
Every minute a message is sent from the Wireless M-BUS Repeater with number of routed packages and the number of routed slots used and sw revision. This message could be used as an indication the device is up and running and the load of the repeater. This message is also used for time synchronizing in multihop system. The battery lifetime is dependent on the time the device is active / not active. The active /not active time can be configured to allow for longest possible lifetime. For example 10 minutes active once per day or 2 minutes active every hour.

ANTENNA
The device have 2 antennas 1 in each direction for maximum RX performance in both vertical and horisontal.  The 2 antennas are also used when transmitting data. All packets are transmitted once on each antenne. The dual antenna will give huge benifits special in buldings where longest possible range is desired.

DEVICES
The Wireless M-BUS Repeater are available in 3 versions:

LAN-WMBUS-R3-M 220V AC/DC. Datasheet
LAN-WMBUS-R3-M24 24V AC and DC
LAN-WMBUS-R3-B High performance battery.Datasheet

For more information please contact us or check the data sheet.

Key features of these devices are:

  • Extend the range between meter and gateway.
  • IP 67 enclosure for outdoor mounting
  • Super long battery lifetime or internal AC/DC
  • 10 years battery lifetime and more.
  • Optional multihop support for extended range.
  • Suppression timer to minimize traffic.
  • Installation mode (route all data).
  • Easy wake-up using a magnet to keep the device active during installation phase.
  • Internal antenna.
  • Enclosure made as uninteresting as possible to avoid sabotage.
  • Dual antennas
  • Maximum range